Take the first Wii remote you wish to sync and remove the door to the battery compartment. I think there is dust inside it and it can't read anything because the dust prevents it to. First, to check the connection there. If liquid leaking from a battery comes into contact with your eyes, immediately flush thoroughly with water and see a doctor. How to Fix It by Replacing The Lens Replacement is actually a pretty simple process. If possible, try swapping the Bluetooth module with a known to determine if that is the cause. Please note that Wii systems bought in 2011 or later may not be compatible with Nintendo GameCube software, and accessories that use the Nintendo GameCube Controller Sockets.
I have had my wii for about 8months now. If the game disc you are using is intended for a region different than your Wii, the disc will not play in your console. I just got a new Just Dance 2016. During the music stopped playing. It has been our experience that the unable to read the disc error often shows up when the laser has stopped working all together. My Wii would not read discs and gave me a few error messages. Brawl The Last Story Xenoblade Chronicles If you are still getting an error, or the error occurs with multiple games and discs, and you are sure the discs are clean and not damaged, move on to step 3.
Power off the console and unplug the power cord for a few seconds. Have you referred to the Operations Manual? I had a similar problem before, and neither of my methods worked. At this point, the error is either occurring because the laser lens inside the Wii the part of the Wii that actually reads the disc is either dirty, or has failed. If there is a lot of dust, use a vacuum cleaner with a brush attachment to remove the dust. Thanks to one of our community members, we have a that may do the trick! Fixing this issue is usually not a matter of just cleaning the lens! If not, move on to step 4. These screwdrivers are necessary to take apart, and reassemble the Wii. It has no problem with any channel other than the disc channel.
At this point, if the connections are fine, you might also want to try a different data cable, though it is not likely that the cable is the problem unless there is obvious damage to it. Whenever I put a disc in my console, it says disc error. Eventually the laser will stop working completely, and when it does you will see this error on every game disc you try to play. If only it were that easy! And other games work fine…. I think there is dust inside it and it can't read anything because the dust prevents it to.
That doesn't mean everyone, just some people. Typically, after pushing the prompted 'A' button, I'll see the screen flash a green color and the following message appears: The system files are corrupted. Replacing the board will be less expensive, but will require soldering. This model is identified by a row of GameCube controller ports along its top or left side, depending on placement. Sometimes cleaning the disc is all you have to do.
I lent it to my bro who returned it with some sort of gunk on the top of the disc. Then the Wii said 'disc error. Additionally, we have the where you can chat as well!. Whenever I put a disc in my console, it says disc error. The Wii shuts down if a lack of ventilation causes the system to overheat. If battery leakage occurs, avoid contact with skin.
The system said it needed updating. The disc giving you the error is most likely damaged, badly scratched, or has a defect and needs repaired or replaced. During the beginning of the fight, he can't use his smash ball. Oh, I had the exact same problem. This handy should be able to aid you! Eject disc and turn off the Wii. If it and the Wi-Fi module are not fully functional and properly attached to the motherboard, the system will not boot. Step 4 Replace The Laser Lens Replacing the laser lens will fix most, if not all, read disc errors.
Cleaning the laser lens can be difficult on the Wii since there is no direct access to the lens. A close friend of mine, who was planning on trading his Wii U in for a Switch, allowed me to borrow his console for this purpose. One day my friends and I were playing Brawl. The process worked flawlessly and I haven't seen any corruption issues since. If your console is placed vertically, the disc label will face to the right. You can clear all previous synced Wii remotes with your console and reconnect the ones you are using. I would like to know ways to get it out if that is the case.
There may be a risk of electric shock sonal injury. The title screen comes up and then the error message that the disc cannot be read. Honestly, this is the only real solution to this problem. Sometimes I'll get lucky and not encounter this error, but most of the time it takes 5-10 power cycles until I can access the vWii menu properly. If they are fine, you may also have to to check the connections from the cables to the board.