Turn signal light bulb B. Haynes Manual Gilera Runner Sp 50 can be very useful guide, and haynes manual gilera runner sp 50 play an important role in your products. Safety rules - If work can only be done on the vehicle with the engine running, make sure that the premises are well- ventilated, using special extractors if necessary;. Haynes Manual Gilera Dna 50 can be very useful guide, and haynes manual gilera dna 50 play an important role in your products. Restore the level and check the absence of losses from the. The battery overcharges the main fuse blows. Therefore, the tank has an intake in the lowest point that sends the fuel to the pump and from here to the carburettor.
Crankcase - crankshaft Splitting the crankcase halves Remove the eight crankcase union fasteners. Specific tooling 020335Y Magnetic support for dial gauge 020074Y Support base for checking crankshaft alignment Refitting the crankshaft - Position the transmission side half crankcase on two wooden supports - Using a thermal gun, heat the bearing seat to about 120°. Spa to be used by the workshops of Piaggio- Gilera dealers. Disconnect the three hoses A towards the engine unit, then remove the fuel pump using the two screws B indicated in the photo. The lighting system bulbs stop working.
If it is necessary to refit the battery in the vehicle, be careful not to reverse the connections, remembering that the ground wire black marked - must be connected to the -negative clamp while the other two red wires marked + must be con- nected to the clamp marked with the +positive sign. Loosen the fitting and restore the tank level. Complete coverage for your vehicle Written from hands-on experience gained from the complete strip-down and rebuild of a Gilera Runner 50, Haynes can help you understand, care for and repair your Gilera Runner 50. The protrusion, measured near the external edge of the disc, must be less than 0. Rules This section describes general safety rules for any maintenance operations performed on the vehicle. Gilera Dna 50 Haynes Manual can be very useful guide, and gilera dna 50 haynes manual play an important role in your products.
The lighting system bulbs burn out. Leave to stand for at least 2 hours; afterwards top-up to the level with sulphuric acid. The problem is that once you have gotten your nifty new product, the haynes manual gilera dna 50 gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Oil mixer tank In plastic, of capacity ~ 1. Introduction Chapter 1: Routine maintenance and servicing Chapter 2: Engine, transmission and associated systems Chapter 3: Cooling system liquid cooled models Chapter 4: Fuel, exhaust systems Chapter 5: Ignition systems Chapter 6: Frame, steering and suspension Chapter 7: Brakes, wheels and tires Chapter 8: Bodywork Chapter 9: Electrical system and wiring diagrams Reference section. Register a Free 1 month Trial Account. Turn signal light bulb B.
Any important changes made to the vehicles or to specific fixing operations will be promptly reported by updates to this manual. Turn signal light bulb B. Take out the brake hose and the speedometer lead from the support bracket anchored on the lower plate. Unscrew the dipstick «A», dry it with a clean rag and then reinsert it, screwing it tightly into place;. Dashboard light bulbs Battery recharge and starting 3. Register a Free 1 month Trial Account. Stoplight switch on rear brake 12.
Front fork Removal Pump unit disassembly - Disassemble the front brake calliper using the two screws. For each breakdown, a list of the possible causes and respective interventions is given. Specific tooling 020331Y Digital multimeter 020151Y Air heater Characteristic Thermostat check: Opening start temperature 60±2°C. Fill the circuit through the expansion tank to the maximum level. Place the scooter on its stand on a level sur- face; 2.
Register a Free 1 month Trial Account. Gilera Dna Haynes Manual Pdf can be very useful guide, and gilera dna haynes manual pdf play an important role in your products. Regular servicing and maintenance of your Gilera Runner 50 can help maintain its resale value, save you money, and make it safer to drive. Front side panels: Remove the screws shown in the photo and then disconnect the joint between the side panels and the lower central cover. Register a Free 1 month Trial Account.
Front Removing the front wheel - Loosen the wheel axle set screws A - Unscrew and extract the wheel axle B. At the end of the charge, make sure that the density of the acid is around 1. Disassemble the carburettor casing using the four screws. Engine capacity 49 cm³ Bore x stroke 40 X 39. Low-oil warning light sender 16.