If not, replace the piston and all the piston rings. Battery 12 V 8 Ah 9. Use proper tools and genuine Kawasaki Mo- torcycle parts. In 1908, a 100-ton Yodo ship, created at the private Kawasaki shipyard, marked the beginning of large shipbuilding. Such a shock to the unit can damage it. Read the pressure at the average of the maximum and minimum indications.
All pages are printable, so print off what you need and take it with you into the garage or workshop. Standard: Link Plates Outside Width 17. Torque - Shift Drum Bearing Holder Screws: 4. Main Fuse 30 A 4. Rear Brake Reservoir Tank 7. Do not use any other battery except for a 12 V sealed battery as a power source. Kz550 Wiring Diagram topic 1983 gpz550 wiring diagram kzrider i m just finding a few connections that don t correspond to the 1982 kz550 wiring diagram 1983 gpz550 wiring diagram 12 jun 2011 01 34 mfolks fline.
If the connecting rod assy was replaced, use the new bolts and nuts attached to the new connecting rod assy. Band Hold the left city light lead and headlight high lead to the upper fairing bracket. If there are obstructions to air flow, remove them. Neutral Switch Lead Connector 34. If they do not, adjust the chain slack and align the wheel alignment see Drive Chain Slack Adjustment.
Good luck and have a wonderful day. The thermostat continuously changes its valve opening to keep the coolant temperature at the proper level. Fuel line clogged Inspect and repair see chapter 3. Gaskets, O-rings, oil seals, grease seals, circlips, cotter pins or self-locking nuts must be replaced with new ones whenever disassembled. Also, check to see that each cotter pin is in place and in good condition. It covers every single detail.
L: Apply a non-permanent locking agent. Motorcycles Harley-Davidson Iron 1200 and Harley-Davidson Forty-Eight Special are inspired by custom-bikes with small rudders of electric hanger, and the fuel tanks are painted in the style of the 70's. Make sure the area is well-ventilated and free from any source of flame or sparks;. Battery 12 V 8 Ah 6. Air in the coolant and needs bleeding. The push rod does not return to its original position once it moves out to take up camshaft chain slack. Main Fuse 30 A 8.
Overall Width 715 mm 28. Left City Light Lead 3. Only appropriate permanent internal repairs are recommended. Clamp Hold the right switch housing lead and fix the clamp into the frame. Fan Fuse 10 A 10. If the indicator does not goes on, go to next step. Removing the rear brake pad is the same as for the front brake pad.
By the beginning of the twentieth century, the company expanded its activities and started producing locomotives, passenger and freight cars, as well as steam turbines. Clamp Hold the rear wheel rotation sensor lead to the brake hose with the clamp at the white mark on the lead. If the motorcycle runs without erasing the service code, the light may light up again. Thrust Washer, 30 mm 1. Guide Run the turn signal relay lead through into the guide. Turn Signal Light Relay Lead Connector 10.
Battery 12 V 8 Ah 7. Main Throttle Sensor Lead Connector 15. Stick coil trouble Inspect see chapter 16. The relays and diodes can not be removed. If the headlight beam points too low or high, adjust the vertical beam.
Such a shock to the water temperature sensor can damage it. L: Apply a non-permanent locking agent. If the connecting rod assy was replaced, use the new bolts and nuts attached to the new connecting rod assy. As they say, guess at once. Detailed illustrations, exploded diagrams, drawings and photos guide you through every service repair procedure. Intake Air Pressure Sensor 4. Overall Height 1 110 mm 43.
Oil Pressure Switch Lead Connector 16. By 1930-1940-m years, the company seriously engaged in the truck-building and the production of spare parts. Spark plug dirty, broken or gap maladjusted Inspect and replace see chapter 2. When this accumulation is suspected or observed, flush the cool- ing system. Main Fuse 30 A 7.