Kawasaki ninja 250r owners manual. Owners manual 2019-02-04

Kawasaki ninja 250r owners manual Rating: 7,7/10 1330 reviews

Kawasaki EX250 Ninja 250R (1988

kawasaki ninja 250r owners manual

If this accumulation is not removed, it will clog up the water passage and considerable reduce the effi- ciency of the cooling system. Such a shock to the relay box can damage it. Ignition Fuse 10 A 14. Illustrations and photographs in this publication are intended for reference use only and may not depict actual model component parts. Set it close to the bottom of the cylinder, where cylinder wear is low. The relays and diodes can not be removed. Torque - Camshaft Chain Tensioner Cap Bolt: 5.

Next

2009 Kawasaki Ninja 250R

kawasaki ninja 250r owners manual

Rotate the crankshaft to positive direction clockwise viewed from output side. Ignition Switch Lead Connector 2. Such a shock to the sensor can damage it. Clutch Lever Free Play Inspection. Battery 12 V 8 Ah 9. Road Clearance 130 mm 5.

Next

2009 Kawasaki Ninja 250R

kawasaki ninja 250r owners manual

In order for the engine, transmission, and clutch to function properly, maintain the engine oil at the proper level, and change the oil and replace the oil filter in accordance with the Periodic Maintenance Chart. Kawasaki Diagnostic System Connector 8. Battery 12 V 8 Ah 13. L: Apply a non-permanent locking agent. Do not drop or shock the valve seat cutter, or the dia- mond particles may fall off. When the fuel hose is disconnected, fuel spills out from the hose and the pipe because of residual pressure. Rear Brake Light Switch Lead Connector 5.

Next

Kawasaki EX250 Ninja 250R (1988

kawasaki ninja 250r owners manual

Thrust Washer, 30 mm 1. If any wiring is poor, replace the damaged wiring. L: Apply a non-permanent locking agent. When inserting the front engine mounting bolt, use the suitable stand under the engine to lift it. Avoid sharp bending, kinking, flattening or twisting.

Next

2007 Kawasaki Ninja 250R

kawasaki ninja 250r owners manual

Toothed Washer, 30 mm 1. Run the reserve tank overflow hose into the guides. . Battery 12 V 8 Ah 8. If the measurement exceeds the service limit, replace the crankshaft. Battery 12 V 8 Ah 16.

Next

Kawasaki EX250 Ninja 250R (1988

kawasaki ninja 250r owners manual

. Kawasaki Ninja 250R Manual Buy the Kawasaki Ninja service and repair manual and learn to perform every service and repair job on your 250R model motorcycle. Then tighten them according to the specified se- quence to prevent case warpage or deformation which can lead to malfunction. Such a shock to the water temperature sensor can damage it. Use the same type and brand of oil that is already in the engine.

Next

Owners manual

kawasaki ninja 250r owners manual

Headlight Fuse 10 A Light 12 V 3. Your Clymer Manuals Kawasaki Ninja 250R 1988-2012 M241 online manual is viewable with a magazine reader and features the same content as the printed manual. If the valve is open, replace the thermostat with a new one. Pull the bulb out to prevent damage to the bulb. Your one year subscription purchase is added to your MyClymer Toolbox and can be accessed wherever you have internet service with your account information. Not only in their clarity, but also you seem to have chosen just the right things to photograph and illustrate. L: Apply a non-permanent locking agent.

Next

Kawasaki Ninja Owners Manuals

kawasaki ninja 250r owners manual

This service and repair manual provides specific, detailed instructions for performing everything from basic maintenance and troubleshooting to a complete overhaul of the Kawasaki Ninja 250 motorcycle. Sidestand Switch Fuse 10 A 21. Rectifier Circuit Inspection W-Y1, W-Y2, W-Y3. These ignition boxes are very reliable, so if you find one on e-bay or at your local salvage yard for a decent price, I would not hesitate to buy it, in all probability it is still good. Special Tool - Flywheel Puller Assembly, M38 × 1.

Next

Kawasaki EX250 Ninja 250R (1988

kawasaki ninja 250r owners manual

This Kawasaki Ninja Manual is 424 pages. Stop the engine, then wait several minutes until the oil settles. Crankshaft Main Bearing Insert Thickness: 1. Make sure the area is well-ventilated and free from any source of flame or sparks; this includes any appliance with a pilot light. This service manual contains many original photographs, illustrations and wiring diagrams obtained from the complete teardown and rebuild of the Kawasaki Ninja.

Next

2009 Kawasaki Ninja 250R

kawasaki ninja 250r owners manual

Gaskets, O-rings, oil seals, grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled. Drive Chain Slack — — — Drive Chain Wear 20-link Length 317. If not, replace the piston and all the piston rings. It's the same place you go if you want to buy a Service Manual. Main Throttle Sensor Lead Connector 3.

Next