Keeway superlight manual english. keeway issues 2019-03-09

Keeway superlight manual english Rating: 5,7/10 399 reviews

keeway issues

keeway superlight manual english

Rotate clockwise the key and unlock it. Keep upper part of body relaxation. If it is seriously worn, replace it. And according to the electrolysis water temperature adjust properly. Basic data Item Standard Service Limit Length of starting carbon brush 12.

Next

Keeway SuperLight

keeway superlight manual english

All the plastic connectors have pawls on them. Use a multimeter to measure impedance value between yellow coil of magneto and ground wire of vehicle block. Outer tube is made up of upper oil pressure cavity and lower oil pressure cavity, piston lever head with piston ring performs tightly with the top end of inner tube, buffer bush is assembled in inner tube assy. Use special or universal tool. Remove brake disc from the front wheel. Check if motorcycle is driven over speed or not at economical speed or driven at low gear; 2.

Next

[PDF] Keeway superlight 125cc manuals

keeway superlight manual english

Ask a question about the Keeway Superlight 125 Have a question about the Keeway Superlight 125 but cannot find the answer in the user manual? Use appointed tester to test. When assembling ratchet-guiding slice, make its upper small arm inflexed can be stopped by the small arm of kicking starter ratchet. Starting clutch removal refers to removal instruction. Please eliminate the carbon deposition in the valve guide with a reamer before inspection. Preparatory data include attentions that shall be paid on all the maintenance operations in the Instruction and Maintenance Manual. Fixing bolt of the tail part of engine Front hanging board of engine 9 Top hanging board of engine 8 Install chain Left cover of engine 7 Install muffle 6 Connect air filter with carburetor Install right rear footrest assy.

Next

[PDF] Keeway superlight 125cc manuals

keeway superlight manual english

Replace it with a new one if abnormality exits. You can now take advantage of member privileges to enhance your online shopping experience with us. In the two-stroke working circulation, there are processes being finished at the same time. Install piston, piston pin and piston pin retainer. Use special tool to install oil seal iii. Tester Vernier caliper Measure shift fork thickness.

Next

Keeway Superlight 125 manual

keeway superlight manual english

Color code of lead of magnet motor and resistances of various coils are the following table Code. Check if there is power Press horn button or slide turn signal light. Function of lubricating system: Function of engine lubricating system is to supply lubricating oil to friction surfaces of engine parts so that dry surface friction will turn to liquid friction between plasmids of lubricating oil. High speed Accelerate it until stopper rises up completely, engine rotates at high speed, which drives velocity of airflow in throat tube and generates great negative pressure in main nozzle hole, and more mixed gas is absorbed out. Turn signal lamp is bright.

Next

keeway issues

keeway superlight manual english

Electric horn does not sound or sound Electric horn sounds loudly. Check Check if fuel switch Remove if valve clearance is too. Power lock assembly 7 Voltage regulator. If you have a specific Keeway Superlight 125cc Manuals pdf in mind, you will definitely be pleased with the wide selection of books that we can provide you with, regardless of how rare they may be. When bearing load on the top of front absorber, inner tube moves down that is to say, inner tube goes into outer tube , or when front wheel strikes on ground, outer tube moves up, in the process of compression, the damping spring and air are compressed in inner tube.

Next

HAYNES : Betriebsanleitung [Englische Version] [M4871]

keeway superlight manual english

Turn signal lamp is dim. While installation, tighten bolt and nut to their specified torque. In reverse, when fuel goes down, floater drives needle valve to go down, needle valve opens, and then fuel is supplied into floater chamber of carburetor. When the gas in the cylinder is compressed, new mixed gases enter into crankshaft case 3. Turn choke valve to its full open position. When assembling foot-starting ratchet, keep pressing mark on the ratchet and the mark on kicking starter shaft at the same level, otherwise noise from ratchet will be produced when engine works.

Next

[PDF] Keeway superlight 125cc manuals: musical

keeway superlight manual english

Wir lernen die besten Wege, um einen Job zu machen und das macht es schneller, einfacher und billiger für Sie. Finally oil lock forms and compression stroke is over. Take down the engine oil filter and release oil pump mounting screw. Washer Cover of oil filter roller Location pin Use an electric or pneumatic tool to screw off locknut. D: exhaust When piston continually moves downward, exhaust gate open, exhaust gas flows out, and the air pressure becomes lower, and at some point, air intake opens, new mixed gases enters into cylinder. This post is not being displayed. Check if gasoline brand being used is too Check cooling system low or the gasoline has been stored for a too long time; 2.

Next

[PDF] Keeway superlight 125cc manuals: musical

keeway superlight manual english

Firstly, air flows across air jet copper canal and atomizes with fuel in foam tube, then is atomized for another time in throat tube. То есть, общие технические характеристики,данные о заправочных емкостях бензина и масла. Check if there is abnormal noise and looseness when the crankshaft is rotating. Convex angle of oil pump cover is dead against the point mark of oil pump retainer. Elbow: put two elbows on natural position and a little close to body. Start the engine and run the engine on idle for a few minutes. Assembling procedure in theory: firstly assemble kicking start axle assy.

Next