They can be in granular form, ready to use and bought in convenient containers for storage. Fit automatic gearbox drain plug and tighten to 15 Nm 11 lbf. Check condition of front and rear axle suspension link mounting rubbers. Refer to Parts Catalogue for full list of colour codes. It is essential that design dimensions and strength are restored in accident rectification.
Position oil pick-up strainer, fit bolts and tighten to 10 Nm 8 lbf. Support transfer gearbox on jack. Each repair is influenced by the extent of the damage and the facilities and equipment available for its rectification. Encapsulated bolts and screws Encapsulated bolts and screws have a micro-encapsulated locking agent pre-applied to the thread. Normal braking will be available. Used engine oil contains potentially harmful contaminants which may cause skin cancer or other serious skin disorders. This is achieved by utilizing engine oil pressure to eliminate the clearance between the rocker arms and valve stems.
Polarity Never reverse connect the vehicle battery and always ensure the correct polarity when connecting test equipment. Crankcase ventilation A positive crankcase ventilation system is used to vent crankcase gases to the air induction system. The sensitivity of these issues will depend on the proximity of the site and the layout and amount of activity carried on at the site. Clean all pulley 'V's, fit auxiliary drive belt, using a 15mm spanner, release belt tensioner secure belt and re-tension drive belt. If fitted, position heatshield, fit mounting rubber to mounting bracket, fit nut but do not tighten.
Street in Key West Game for a little exploration? Position alternator mounting bracket, fit bolts and tighten to 40 Nm 30 lbf. As an alternative, some bolts and screws have the M and strength grade symbol stamped on the flats of the hexagon. Check all fluid levels and top-up if necessary. Fully extract seat belt and allow it to return under its own recoil mechanism. Inlet and exhaust valve stem oil seals are fitted at the top of each valve guide. Tighten nut securing mounting to gearbox bracket to 48 Nm 35 lbf. Always ensure that replacement bolts are at least equal in strength to those replaced.
Check operation of seat slide and tilt mechanisms, ensuring there is no excessive play between seat cushion and seat back. Position an axle stand under right hand axle tube 4. Position ignition coils and connect ht leads. Repeat this procedure until adapters are removed. Noting that bolts 1, 3 and 5 are longer than the remainder, fit cylinder head bolts and tighten in the sequence shown to 20 Nm 15 lbf. Release ht leads from clips on rocker cover.
Fit rear underbelly panel if fitted , secure fixings. Oil from the filter passes into the main oil gallery and through internal drillings to the crankshaft where it is directed to each main bearing and to the big-end bearings via numbers 1, 3 and 5 main bearings. Where necessary, additional specific precautions are detailed in the Restraint Systems section of this Manual which should be referred to prior to commencing repair operations. Stub pipes for crankcase ventilation hose connections are fitted to each rocker cover, the pipe in the right hand cover incorporates an oil separator. Impacts which do not deploy the airbags or pre-tensioners Check for structural damage in the area of the impact, paying particular attention to bumper armatures, longitudinals, crash cans and bracketry. The foul drain will accept many of the normal waste waters such as washing water, detergents and domestic type wastes, but oil, petrol, solvent, acids, hydraulic oil, antifreeze and other such substances should never be poured down the drain.
Fuel: l don't run engines unnecessarily; l think about whether journeys are necessary and drive to conserve fuel. Remove 4 rear facing bolts securing sump to bell housing. Degree, angle or temperature dia. Place a suitable container beneath gearbox. Clean magnet in oil drain plug. View of buildings on the coast of tropical island San Andres y Providencia Even at first glance, looks like the quintessential Caribbean hideaway. If there is no designated storage area available, store in the luggage compartment of the vehicle and inform the workshop supervisor.
Also, refrigerant cylinders and replenishment trolleys when discharging will freeze skin to them if contact is made. Waste materials stored on open ground could also leak, or have polluting substances washed off them that would contaminate the land. Clean area around filler cap, remove cap. On assembly, add the quantity of refrigerant oil drained to the new component. If paddling wears you out, just jump in for a refreshing swim in the crystal clear island waters. Roll pins Always fit new roll pins of an interference fit in the hole.
The hand brake acts on the the transmission, not the rear wheels, and may be ineffective when the wheels are off the ground. Handling and storage of waste Ensure that waste materials are not poured down the drain or onto soils. Do not attempt to straighten with a single pull but rework the damaged area using a series of pulls, releasing tension between each stage and using the opportunity to check alignment. Or: Finally if you like this page with Land Rover manuals and part catalogues please buy a paper copy or make a small donation! Engine oil viscosity The above chart indicates the ambient temperature ranges which each engine oil viscosity is suitable for. Remove 2 nuts securing engine mountings to chassis.